Blood stains can be especially tricky to remove from carpet, but if you follow this guide on how to get blood out of carpet, the process will become much simpler. In just five steps, you’ll learn how to effectively deal with this potentially difficult situation and remove your blood stain from carpet in no time at all.
1) Evaluate the Stain
A blood stain is one of the most difficult stains to clean, but it doesn’t mean you’re doomed. Follow these five steps and you’ll be on your way to removing that unsightly stain in no time:
- Take a damp cloth and blot any obvious stains using cold water. Don’t rub too hard, or else the stain will spread.
- Mix dish soap with cold water until it’s well-mixed. Dip a sponge into the mixture, then start dabbing at the stained area with a light hand. This should lift some of the dirt and blood out of the carpet fibers without hurting anything else in its path. Rinse out the soapy solution by dipping your sponge back into the bowl and squeezing the excess liquid off.
- Blot again with a dry towel. The process may take several tries, so don’t get discouraged!
- Cover all stained areas with hydrogen peroxide (half a cup). Let sit for 30 minutes before rinsing away any excess liquid with cold water.
- Use paper towels to absorb as much moisture from the carpet as possible – this will help make drying easier later on.
2) Select Your Supplies
- Use a clean white cloth or paper towel to blot the area where the blood has spilled. Blotting will remove as much of the spilled blood as possible.
- If your carpet is light colored, use hydrogen peroxide or dish detergent and water on a clean white cloth or paper towel.
- If your carpet is dark colored, you can try using a little bit of dish detergent and cold water on a clean white towel or sponge, but be warned that this may make the stain lighter in color, which could ruin your carpet’s appearance permanently if you don’t act fast enough before it sets in.
3) Create a Mixture
If you’re looking to tackle the blood stain yourself, be sure not to use any type of detergent on the carpet. Instead, blot up as much as possible with paper towels or a clean cloth. Next, pour hydrogen peroxide onto the stain and let it sit for about 10 minutes before you apply dish soap. Dab dish soap onto the spot with an old toothbrush and use your fingers or a clean cloth to scrub it out of the carpet. If this doesn’t work, try pouring salt over the affected area and then covering it with a wet rag before letting it sit overnight.
4) Apply the Mixture
- The first step in removing blood from carpet is to find out how old the stain is. If it has not been cleaned up yet, you need to act quickly and use a dry, absorbent towel or paper towel to blot the area and absorb as much blood as possible. If the stain has already dried, then you need a mixture of one part liquid dish soap with three parts water. Apply the mixture on the stain and allow it to sit for 15-30 minutes before scrubbing it off using a soft cloth or sponge.
- Next, take white vinegar and mix it with cold water in equal parts (1/2 cup). Pour this over the stained area and wait about 10 minutes before scrubbing off the blood with a wet cloth or sponge.
5) Rinse and Repeat as Needed
- Rinse the spot with cold water.
- Apply a thick layer of liquid dish soap and scrub with a brush. Use as much as you need to remove the stain, but don’t let it dry on the carpet or rug. Allow it to sit for five minutes before rinsing again with cold water; repeat until the spot is gone or until there’s no more blood on your scrub brush.
Check related video on DIY Carpet Cleaner channel:
Congratulations! You’re on your way to a blood-free carpet. These tips should help you get the job done quickly and easily. Remember, if you’re not sure how much time you’ll need, don’t overdo it by trying to scrub too hard or use too many products. If you go slowly, take breaks as needed, and be patient, the results will speak for themselves.